Klubersynth VR 69-252 N

Manufacturer: KLÜBER LUBRICATION (Germany)

Special lubricating grease for drinking water taps containing e.g. EPDM and/or NBR elastomers
Klübersynth VR 69-252 N is a tailor-made, highly adhesive, light-colored lubricating grease based on fatty oil, calcium soap and PTFE. With a carefully selected combination of active substances, this lubricant offers very good performance and high functionality combined with a long service life. Klübersynth VR 69-252 N clearly surpasses the load alternation requirement of 200,000 cycles at a closing force of 2.5 Nm and is therefore in full compliance with the European standard DIN EN 200. Klubersynth VR 69-252 N meets the new drinking water and plastics guideline (KTW) of the German Umweltbundesamt (Federal Environmental Agency) and conforms to the current French positive list for drinking water applications ACS.

Benefits for your application

Longer component life due to less friction and wear, especially in brass spindle valves.
Prevention of stick-slip at high tightening torques and 500,000 load cycles.
A lubricant for all components meeting all technical, design and chemical requirements, e.g. the German KTW and the French ACS Guidelines.
Cost-saving as lubricant can be applied by brush or using fully automatic mass application techniques.

Orther products

Product

Features, Application

Unisilkon L 250 L

Special lubricating grease for drinking water, beverage and heating valves and fittings
UNISILKON L 250 L is a special lubricant based on silicone oil and PTFE with high thermal stability. Owing to its relatively high viscosity, adhesion is improved even in case of unfavourable geometries. It is resistant to cold and hot water, superheated steam up to approx. 130°C as well as industrial cleaning agents and disinfectants. It is also resistant to pumpable foodstuffs and beverages like fruit juices, beer or milk products.

Klubersynth V 64-300

Synthetic lubricating grease for drinking water taps
Klubersynth V 64-300 is a special lubricating grease based on a synthetic oil with a low content of silicone oil and an inorganic thickener.
This product complies with the recommendations pertaining to synthetic materials in contact with drinking water set forth by the German Health Authority. It has a high load-carrying capacity and excellent wetting properties.
Klubersynth V 64-300 is NSF H1 registered and therefore complies with FDA 21 CFR § 178.3570.

Nosol GBY 2

Fully synthetic lubricating and sealing grease for valves and fittings
NOSOL GBY 2 is a fully synthetic lubricating and sealing grease for valves and fittings, especially gas fittings and bearings. It is resistant to water, mineral oil, glycol-water mixtures, gaseous and liquid aliphatic hydrocarbons such as town gas, long-distance gas, natural gas, petroleum gas and their substitute gases as well as to propane and propane-butane mixtures.

Kluberlub BVH 71-461

High-temperature lubricating grease for bearings and valves
Kluberlub BVH 71-461 is a special lubricating grease based on mineral oil/synthetic hydrocarbon oil/polyurea. It has a wide service temperature range and is suitable for rolling bearings up to a service temperature of 160 °C.
Kluberlub BVH 71-461 ensures excellent wear protection, and its EP additives provide a high pressure absorption capacity.
It is very adhesive and resistant to water under static and dynamic loads.
Kluberlub BVH 71-461 is also particularly resistant to oxidation and ageing and reliably protects against corrosion. It has an especially high sealing effect in coke oven valves.

Syntheso GLEP 1

Special lubricating grease with EP additives, compatible with EPDM
SYNTHESO GLEP 1 is a special lubricant for a wide variety of applications with an almost neutral behaviour towards many elastomers (including EPDM) and plastics (except PC and ABS). SYNTHESO GLEP 1 can be used in a wide service temperature range and offers efficient protection against wear, good adhesion and resistance to water.

Paraliq GTE 703

Synthetic lubricating grease for valves, fittings with EPDM seals
PARALIQ GTE 703 is a special lubricating grease based on silicone oil and PTFE.
It is registered as NSF H1 and complies with FDA 21 CFR § 178.3570. It was especially developed for the incidental contact with products and packaging materials in the food-processing, cosmetics, pharmaceutical.
It may also be used for very low-load rolling bearings used in the beverage industry where an EPDM-compatible H1 lubricant is required.

Technical service

Supervising installation of Aumund equipment

Organizing technical training courses, technical workshops at customers' factories

Lubrication consultation and recommendation

Automatic lubrication system design and installation

Gap measurement in vertical grinding machine

Repair lubrication spray service

Address: Room 503, 5^thFloor, 101 Lang Ha Building, Dong Da Dist., Hanoi, Vietnam
Phone: (+84.24) 3562 6208
Hotline: +84 911 54 2416
Email: [email protected]

Address: 68 Le Manh Trinh Street, Phuoc My Ward, Son Tra District, Da Nang City, Vietnam

Phone: (+84.236) 394 3203

Hotline: +84 911 57 2416

Address: Room 10, 9^thFloor, An Khang B Building, An Phu Ward, Thu Duc City, Ho Chi Minh City, Vietnam
Phone: (+84.28) 6281 3200
Hotline: +84 911 04 2416